"problem" : 255 results during the last 30 days
Your search in 0.214 s
05 Jul 00 : 44 | Full floater---locker So after the Rubithon there started a loud bang in my rear axle. The culpret was one of the spreader nuts on the hub was for all practical purposes all the way unthreaded and the threads on the hub were a bit buggered up. I managed to get it all back together by backing the inner nut and cleaning up... Source : IH8MUD Forums 2 hours ago |
05 Jul 00 : 29 | Steering arm vs. wheel back spacing I just installed my new used fj62 steering arm on my 40 and it looks good. My problem is that with my wheels back spacing it rubs on the tre boot and destroys it. Question is...should I heat and bend the arm in a bit or get some of the wheel spacers(1") and install that and not bugger up the... Source : IH8MUD Forums 3 hours ago |
04 Jul 17 : 50 | Help! Hey everyone. Well, I just got my 1987 60 home yesterday. I am wanting to do some fluid changes, tune up etc... my problem... I dont have many tools or a ton of experience with auto repairs. I have done ouil changes in the past changed starter and fuel pump on a 77 chevy monza, but other than that... Source : IH8MUD Forums 9 hours ago |
02 Jul 04 : 51 | Another T-Case problem Ok, I went out to do a little four wheeling in my 75 fj, got out and locked the hubs, shifted to 4h and my t-case wouldn't go into 4-L. After making a short loop I got back to the main road unlocked the hubs and it wouldn't shift to 2wd. Not wanting to make the 30 min. trip back home in 4wd I... Source : IH8MUD Forums |
01 Jul 02 : 41 | fast idle problem After a few weeks, I still haven't figured out the fast idle problem I'm having (around 1300 rpm) with my 77FJ. It all started when I sprayed a little carb cleaner around the butterfly when I was changing my air filter. With some help from Pinhead, I found the third hidden idle screw and turned it... Source : IH8MUD Forums |
01 Jul 02 : 04 | 2L oil pan clearence problem in IFS truck?? will a 2L from a solid axle truck have any clearence issues in an IFS rig? someone told me that the oil pan will not clear. if that's true, anyone know any sources for an ifs 2L oil pan? thanks! Source : IH8MUD Forums |
30 Jun 13 : 02 | compression problem So I have a 1985 fj60 with a compression problem. when i got the thing it would start sometimes and sometimes it was hard to get going. since then i have rebuilt the carb, put in new plugs, wires, distributor cap, rotor, and coil. also have changed oil, transmission fluid, and radiator fluid. I was... Source : IH8MUD Forums |
04 Jul 07 : 47 | My 2F is tired.......consider my options for me. Grab a drink this is long winded........................ My 86 FJ 60 has 235,000 miles on it and is getting tired, carb needs rebuilt, using 1 quart of oil every 450 miles, The bottom of the motor has a little oil here and there but no major leaks, never leave a drop on the ground. It could use a... Source : IH8MUD Forums 19 hours ago |
04 Jul 05 : 11 | Stuck piston ring diagnostic help on H I've been having compression troubles with the H in my 1980 HJ45. When I got the truck it ran like crap. Did a compression check and leak down test which revealed loss of pressure on cylinder #4. Leak down showed the rings to be the likely culprit. I did a couple of overnight Seafoam soaks and... Source : IH8MUD Forums 22 hours ago |
30 Jun 00 : 38 | Recirculating Air Problem? The Texas heat is here in full force. I knew my A/C didn't blow near as cold as my other 80, that thing would freeze you out at idle. I was thinking about cleaning the evaporator via the fan hole. I was first stumped by the recirculating air flap in the bottom of the fan housing. While looking at... Source : IH8MUD Forums |
28 Jun 19 : 48 | RT Help needed - electrical problem... ...and on vacation - so I don't have my local resources (my mechanic). All interior lights not working (clock, dome, parking lights, heater, tail/brake lights - the biggest problem). Strange thing is that headlights do work. I checked all fuses and are ok. What should I look at next? Source : IH8MUD Forums |
04 Jul 01 : 52 | over heating Hello to all you cruiser heads. Here is my problem. 1977 2F motor rebuilt just installed with a NV4500. I have an electric fan between the radiator and the motor. Running around town I can run with the fan off as long as the lights are not to long then when it starts to heat up I flip on the fan an... Source : IH8MUD Forums 25 hours ago |
04 Jul 01 : 41 | Picture Problems I have been trying to upload a few pictures today and keep getting error messages. These are pictures that have not uploaded in the past. I loaded a couple from old posts, no problem. File size is good...any idea's? Doug Source : IH8MUD Forums 25 hours ago |
04 Jul 00 : 07 | 2F rebuild round 3 - It's finally running! My wife and I took the week off and the weather has absolutely sucked so I spent a few days in the garage and finally got my cruiser all put back together and running. For those who missed out on rounds 1 and 2 I assembled my motor and missed the 4 freeze plugs in the side of the block in behind the... Source : IH8MUD Forums 27 hours ago |
28 Jun 03 : 03 | brake problem ... fronts ... master cyc I am having a problem with my front brakes. They lockup after a few tough stops, and when i bleed off the pressure down at the wheel where the bleed port is at, they have pressure on them with no peddle applied. is my problem with the vacuum assist or is it the master cyclinder the problem? maybe a... Source : IH8MUD Forums |
03 Jul 19 : 24 | Great Customer service! I recently sent the input shaft of a new to me SM420 to Novak for them to machine the shaft for a seal. I ordered the conversion online, 3 days later the new nose cone is at my door. I had just mailed the shaft to them the day before. Get a call from them, the gear on the shaft has a good gouge in... Source : IH8MUD Forums 32 hours ago |
03 Jul 18 : 29 | Elemenrty Algebra. killin me Completing the square to solve a Quadratic Equation Problem: X2 +4x = -1 X2 +4x +4 = -1+4 it is X squared BTW>> Where does the 4 come from? I am trying to get a jump on this crap cause MATH SUCKS Source : IH8MUD Forums 33 hours ago |
03 Jul 17 : 45 | Oil leak The attached pic is taken from the FSM with pointers to my problem area. I'm hoping to source a gasket without ordering the gasket set shown in lower right (would someone confirm this is the gasket for me?). Can this gasket be had independent of the complete set? Or, will RTV hold a seal in this... Source : IH8MUD Forums 33 hours ago |
26 Jun 02 : 28 | V8Swap starter problem I'm having a problem wiring up the starter in my v8 swap. Tested the starter everything is good. The positive from the battery is good, I grounded it just to test so ground is defiantly good. The power from the ignition hits 12v when I turn the key but will not engage the starter? When I have... Source : IH8MUD Forums |
26 Jun 01 : 22 | Starting problem ?? sometimes. 73 fj40. The problem has only happened a couple times and fixed itself once without me trying anything. When I turn the key forward to the starting position the amp gauge moves but the starter does'nt turn over. I did the old trick of crossing the celinoid with a screwdriver and it cranks over fine.... Source : IH8MUD Forums |
23 Jun 13 : 59 | Possible SM465 Problem I have had an occasionally reoccurring problem that I have not been able to isolate but I think I have determined it to be in my SM465 trany. Once in a while, while in reverse there will be a binding to the point where it stops the truck and a few times it binds and then a loud pop. I have only had... Source : IH8MUD Forums |
03 Jul 00 : 21 | The Equalizer Hi All Having the transmission to transfer case oil movement problem and I'm wondering if anyone has tried to install some kind of tube from the transfer fill hole to the tranny drain plug to equalize the situation? Thanks Attached Images Source : IH8MUD Forums |
22 Jun 05 : 28 | FJ40 Gas Tank Problem Question My brother finally decided to get his 73 back on the road. He installed a new fuel pump and can get the cruiser to run out of a jar but not the tank. He has blown out all the lines and they are free. He removed the tank and tried running a wire through all the feeds from the tank. All are clear... Source : IH8MUD Forums |
21 Jun 22 : 56 | I've got a little insect problem.... So far nothing is working. Any suggestions? Source : IH8MUD Forums |
02 Jul 15 : 55 | running rich the bad way! Hello, I have been following this site for a couple of years now, I own a '96 fj80 and '74 fj40. I found that what ever problem I've had in the past from; check engine light (oxygen censor) to break adjustment the answer is always in old threads in your forum. So I would like to say Thanks. I'm like... Source : IH8MUD Forums |
02 Jul 16 : 03 | Terrific FJ40 Upgrade... '71 FJ40; F Engine. I have a non-vacuum distributor which requires a mechanical distributor. Ordered a Mallory hi performance Unilite 454101 digital distributor with infrared triggering (totally maintenance free), 29216 hi-output coil; 29351 active power filter...hooked them up in less than 2 hours... Source : IH8MUD Forums |
20 Jun 13 : 37 | 96-00 Vortec Problem 135,000 miles, well maintained as in I've owned it since new. Started bucking on startup, intermittent at first, now more consistently. Put on a new starter, same thing. I suspected head gasket but pulled plugs and there is no coolant in the cylinders at all. Small coolant leak at the back of the... Source : IH8MUD Forums |
19 Jun 18 : 54 | FJ40 Rocker Arm Oiling Problem? Hi Guys and Gals. I have a 1977 FJ40 and before I tear it apart, I wanted to ask a question. How much oil should be getting to the top end (Rocker Arms). I know in some vehicles, if you take off the oil filler cap with it running, you have a mess. Not so on my 2F motor or on my friends F motor. I am... Source : IH8MUD Forums |
02 Jul 04 : 49 | Toyota Sienna Run Flat issues? Grandma bought a fully loaded AWD Sienna in '07. It came with the run flat tires and tire pressure system. Around four months after she bought it the tire pressure light came on and I added air in one tire. Two months later it came on again and I added air again. Two months later on again. This time... Source : IH8MUD Forums |
01 Jul 21 : 00 | Brake issues with my 100 I have an '04 LC-100 series. When the brake pads were ready to be replaced, I took it to a brake shop that did great work on my old 80-series. After getting the work done, we experienced some bizarre, soft-pedal/push to the floor to get the rig to stop behavior. While unnerving, the problem was... Source : IH8MUD Forums |
01 Jul 20 : 17 | Real Time Help - 3b alternator Hey all, quick alternator problem this time. My poorly attached AC compressor finally jumped off the front of the engine (hasn't had a belt on it for a while). No biggy except that when it did so it took something vital for the alternator to function with it. I'm pretty sure it's REALLY simple, but... Source : IH8MUD Forums |
01 Jul 15 : 56 | Spare Tire Mount? I use the stock undertank spare tire mount with a 33X9.5X15 tire on a stock wheel. As many have noticed this is not the most secure mount set up as the tire can rock a little bit. On my 60 the stock size tire/wheel moved about tha same amount as the 33". I have used some stiff wall rubber hose as... Source : IH8MUD Forums |
01 Jul 01 : 37 | Cruiser Rust - WWMD what would a mudder do I have had my locked, lifted, and loaded 97 w/ 113,000 mi. since December 08, Picked it up from a fellow mudder ERRATIC in New Hampshire and it now lives with me on the shore of Connecticut. Attachment 336523 Not my only cruiser but it defiantly has the least amount of rust. Problem is now... Source : IH8MUD Forums |
30 Jun 23 : 33 | Carb Troubles - 76 2F I posted this in the 40 & 55 Tech, but no responses. Hopefully someone here can shed some light. I have a 76 Fj55 that i have been chasing the bugs on. The PO didnt drive it much for 3 years and I want to drive it all of the time. It got to the point where I had chased everything down to the carb... Source : IH8MUD Forums |
30 Jun 17 : 37 | Need a manifold Has anyone got a stock exhaust manifold and the y-pipe for a 22r? for borrow or purchase? Smog shops are giving me trouble for my CA smog legal header....first time i've had this problem in the 4 years it's been on there. If anyone has anything please let me know, that or a 3rz would be nice too.... Source : IH8MUD Forums |
30 Jun 13 : 03 | fuel pump replacement I got my fuel pump off and cleaned the area up. Got my new kyosan pump from JT off road and went to put it on. The directions told me to make sure that I put the spacer back in between the block and the pump or else it could destroy my pump and or my crank. The problem is that my old pump did not... Source : IH8MUD Forums |
30 Jun 05 : 04 | fuel pump plug?? catastrophic failure or?? here's what caused my 'crank-no-start' problem friday; the plug at the top of the pump "melted?" or disintegrated enough that the power pin in the plug was not doing its job. so, um- :meh:how close to catastrophic was this failure? anyone seen something like this? my LH low beam looked very similar,... Source : IH8MUD Forums |
30 Jun 02 : 01 | grind going from L-H? I need some advice here.....Today I tested the H-L selector and I had a grind going back from L -> H. I have a 95 w/ CDl switch and the pin 7 mod. Heres What I did: Stop Truck, Put it into N, move selector from H->L. No problem. Then after testing it, I decided to put it back into H. Stop Truck... Source : IH8MUD Forums |
29 Jun 20 : 35 | Good 80 Mechanics in Denver area?? 80 noob needs a good toyota mechanic in the Denver Area. With the family growing I decided to make the plunge and buy an old 80 to fix up. Ended up getting a 93 with a lot of miles but, didn't think that mattered cause I know you can drive these rigs till the wheels fall off. The problem....I can't... Source : IH8MUD Forums |
29 Jun 20 : 09 | The Trouble with Dribbles - Carb Issues I have a 76 Fj55 that i have been chasing the bugs on. The PO didnt drive it much for 3 years and I want to drive it all of the time. It got to the point where I had chased everything down to the carb and I was dragging my feet on rebuilding it. So then I pulled it off and just rebuilt it. When I... Source : IH8MUD Forums |
29 Jun 14 : 24 | Album Pics Don't Display Woody, Two screen shots attached. Maybe it's my work computer. In my build thread I've linked to some pictures placed in my Album. As you can see from the screen shots, the captions show, but the images don't. Any ideas? They did show at home yesterday, but I've not had this problem before at work.... Source : IH8MUD Forums |
29 Jun 11 : 25 | diff gears what should i do.. hey all, im kinda new to the 80 series, and 4x4s in general really.. so heres my problem,probelly really stupid.. (and i have looked but cant find the answer i want) Ive got a 3.5" lift and 315/75/16s tyres, now i need to change my diff gears.. as its an all wheel drive does this mean i need to... Source : IH8MUD Forums |
29 Jun 03 : 28 | blinking dash lights has anyone experienced dash lights going on and off at times? though not often. newby here, i cant find an existing thread to this sort of problem. by the way i drive an HDJ81. if any soul out there could link me to an existing thread or help me directly through this thread. i did some research and... Source : IH8MUD Forums |
29 Jun 05 : 39 | Replacement Sun Visor My sun visor broke and wont stay up!!! (I know, when it gets old, it wound stay up any more) It was not like the other visor problems with the worn shaft, mine broke where the wire sits in the clip. Is there a replacement for the sun visor like from another vehicle? Found some used but not sure if... Source : IH8MUD Forums |
28 Jun 18 : 55 | real time: cant get over 75km with out coughing black smoke i just started driving my fj40 i finally finished building it. its a 1976, i have rebuilt the carb. so today was the first time i tried going over 60km. i can mkae it to 70 but then the engine starts to cough and sputter. while shooting out black smoke out the exhaust. im running the stock mech pump... Source : IH8MUD Forums |
28 Jun 14 : 15 | 4 Runner rear window button not working I have a 96 Runner. I can no longer roll the rear window down from the button on the center console. I can raise an lower the window from the key hole in the rear still. Suggest on how to fix anyone else have this problem Source : IH8MUD Forums |
28 Jun 04 : 56 | 396 trying to turnover after ignition turned off. Been lurking for awhile following buildups and finally decided to sign-up. I have a 72 FJ40 with a 396 BBC. When I turn off the keys to the ignition the motor wants to keep turning and turns over once or twice (without catching) until I turn the igntion back on to turn it on. On a possible related... Source : IH8MUD Forums |
28 Jun 01 : 52 | help identifying engine noise hello...and help! background: the vehicle in question is a BJ60, 3B with a garrett turbo, 5 speed, 385k kms. just drove home (3 hrs. from mechanic to home) from having rebuilt injectors installed, new diaphragm installed and the rest of the fuel system gone through. as well, rocker system was... Source : IH8MUD Forums |
27 Jun 14 : 00 | DC Area - Anyone up for some wrenching? I'm going to be tearing into my engine this morning in the attempt to identify the misfire / shuddering problem. If anyone's in the McLean, VA area and wants to swing by to lend a hand, watch from a distance, work on your on your own project, or just crack a :beer:... come on by. Got some Dale's... Source : IH8MUD Forums |
26 Jun 19 : 48 | Transfer Gear Output gear bushings Hi Folks, new here, have always been in the abckground reading. I am Oliver and own a Toyota 1985 LJ70. Currently refurbishing the tranny and transfer case. So far so good, all needle bearings, synchros, main bearings and c-clips were exchanged in the tranny. As for the transfer gear, I figured to... Source : IH8MUD Forums |
